|Manufacturer||starlight (other LEDs from starlight)|
|Fitting Type||Kit (other Kit LEDs)|
|Light Type||Downlight (PAR)|
|Review Notes||Manufacturer recommends this as a replacement for 50W halogen globes. Includes LED power driver RAV1201. Driver carries RCM and CE approval markings. Compatible dimmer types are not specified but dimming on a Clipsal 32E450UDM universal dimmer was acceptable (see results below). Dimming range was 0-100%, which is better than most other phase-cut dimmable LED drivers. While dimming did not result in any visible flicker, performance was not very smooth; its dimming range was mostly contained within a very narrow range of travel. Measured lumen output was significantly lower than manufacturer's claims.|
|Price||$24.20 (AUD) from www.l-e-d.com.au on 6th of August 2014|
|Watts||9W||8.9W @ 242V |
LED Driver Transformer
|54.7W @ 12V|
|Yearly Running Cost[?]||$1.97||$1.95||$11.98|
|Lumens||720 lm||457 lm||765 lm|
|Efficiency[?]||80 lm/W||51 lm/W||14 lm/W|
|Lumens/Purchase Price||30 lm/$||19 lm/$||170 lm/$|
|Color [?]||Warm White, 3000K||Warm White, 3099K||Warm White, 3015K|
|Dimmable||Yes, Trailing Edge||Below average||Yes, Trailing Edge|
|CRI (Color Accuracy)[?]||85||81|
|Life||40,000 hours||Not Measured||6,000 hours|
|Min/Max Voltage||180V / 265V||N/A|
|Min/Max Temperature||N/A / N/A||N/A|
|Measured Temperature||60°C @ 25°C ambient
140°F @ 77°F ambient
|256°C @ 25°C ambient
493°F @ 77°F ambient
Link to manufacturer specifications at time of testing
Graph notes: Dimming performance can be highly dependant on the type of dimmer, the number of lights in the circuit and other factors. Results in your house might vary. Mouse over the graph for more details. Position 10 = Not dimmed. Position 1 = Fully dimmed.
Angle: 74° (±37° from bottom), Maximum lux:
Graph notes: Shows the intensity of the light when viewed from different angles. Normal omni-directional globes have a fairly constant output all the way around (excepting directly above). Downlights have a narrow range at the bottom in which the light is emmited, this determines their angle.
Graph notes: Shows the breakdown of the LED light into its component colors. With short wavelength ultraviolet on the left and long wavelength infrared on the right. The green line represents the relative absolute strength of the light at each frequency, while the red line represents what the typical human eye would see. The human eye is most sensitive to green light, but much less sensitive to purples and deep reds.
Percent: 22%, Index: 0.063 (lower is better in both cases)
Graph notes: Shows variation in light output over 1/10th of a second, with relative light output on the Y axis and time on the X Axis. Measured with a photodiode connected to an Oscilloscope. Ideally the yellow line should be flat. Low frequency high amplitude waveforms mean there is a possibility of noticeable flicker, but sensitivity to flicker varies between people. [More details about LED flicker]
|9W CW COB LED Downlight||$24 (AUD)||8.7W||641lm||82lm/W||Cool White, 6092K||70°||Kit|
|9W WW COB LED Downlight||$24 (AUD)||8.9W||457lm||80lm/W||Warm White, 3099K||74°||Kit|
Disclaimer: While every effort has been made to ensure the accuracy of these results, each measurement carries an inherent degree of uncertainty and error. Safety and EMC compliance of products to regional or international standards have not been verified unless noted as an ENERGY STAR® LED Lighting Facts, or SSL Quality Scheme certified product. Retailers and importers selling unmarked or unapproved electrical goods can be fined or imprisoned. Mains supplied downlights require installation by a licensed electrician.